Maintenance of wooden furniture

Maintenance of wooden furniture

Important things to do maintenance of wooden furniture and repair the defect before the increase and in some cases lead to the replacement of this part of the furniture and this will cost a lot in light of the steady increase in the prices of furniture.

Will be exposed as follows for defects that may occur to Dilv tires of different types and kitchens, beds and cupboards legs and chairs.

Dilv tires

Apply the word wheel on the buffet and Alnich and hairstyle and Alnich and Alcolmodino, usually ride this Aldilv using a couple of heel where the husband the upper fixed (the female in the body of the wheel and the male in Aldilfah), while the pair lower, the female mounted in the body of the wheel and the male bulk put in place so down in cavity prepared for that in Aldilfah, in the case of jaw Aldilfah are opened half slot and then pull out from the bottom until withdrawn from the heel, taking into account the ban so as not to fall on the ground when pulled and movement down to rid it of playing top, and is limited to crashes Dilv tires in the fall of the place or can not be closed easily and in such cases are examined Aldilfah particularly in terms of heel bottom may be the result of a break in the lip barrier to mention the heel (back) or have a parts Stub installed may break, if it became clear that one of the parts may break from his place is re- install it by linking it with nails Burmh using the screwdriver.

If the result of a broken heel where to install the upper part, it is fixed place of installation (replaced) by following the following steps:

After decoding processing Aldilfah is a place for a new piece of wood (usually beech) using a chisel and Adakkmag.

Processing is a piece of wood so that they are the same dimensions at the same level after installation.

Hammering a nail rod in the appropriate length of the new piece in two places are not mutually exclusive with places Alborma nails used to install the stub.

Placed a layer of glue on the surface and the installation may be completed cuneiform hook is cleared and increases the glue using a damp towel with water and with picture.

After making sure the glue is dry prove (Ntaiya) Stub Burmh nails using a screwdriver and try Aldilfah work.

In the event of a break in the barrier Stub (Curling), it is removed an area of ​​suitable length equal to twice the place Stub using the chisel and Adakkmag very carefully so as not to be affected by plywood envelope of the leaf, and are fitted with a piece equal to the drilling of beech wood and fastened in Aldilfah using glue, and is being drilled place of the tongue and heel riding Aldilfah and try.

Maintenance of woodwork - easy ways

3 - Kitchen furniture

Limited to damages that occur in the kitchen furniture as follows:

Take off one of Dilv Kitchen result dislocated Detailed: In this case an attempt is made to install and if the screws Alborma does not accept the link, it will be changed as little of or using the Quayle high instilled in glue and hammer in place of the screw and leave to dry then re-installed detailed again using the same pins.

Break in one of the hinges: This change requires Bokhryjdidh of the same type, size, and is being installed using a screwdriver nails Alborma habit.

Formica left the place, but sound: In this case, loosen Aldilfah is complete lifting of Formica from the surface using the Iron medium heat moved on Formica with caution brought slowly to the top, is cleaning the back of Formica and wood from the effects of glue old and that by rubbing the surface plate saw Haddadi or knife paste, painted wood surface and the back of Formica with a layer of glue fast (glue Formica) and waits for a quarter of an hour, and then paste the Formica by clicking on it from the inside out even expel the air and we get the adhesion completely, and pressed Aldilfah under the influence of the weight to dry and then mounted Aldilfah.

May be Formica is broken and has to be changed: In this case, the cutting portion dimensions required plus about half a cm increase on each side. Are off Formica old using Chisel or knife gently, so that no damage to the wood beneath it, and cleans the surface and painted with glue rapid and waits for a quarter of hours and then being pasted Formica where they are to start by heading to the other side in the case of Aldilfah long it can start from the middle of Alsafah heading to the outside and pressed and wait until dry and then removed the increases in Formica using a radiator and is made Albaradh in one direction (the direction of the pressure on Formica)

Damage to the plywood: either to leave his place in this case can be re-installed using glue and screw hook.

But if necessary change the plywood is scaled and cut the required piece using alligator thieves and clear the edges using a coolant Alkhhabbi then fixed in place with glue and screw hook.

4 - Family

In the case of vibration of the bed, this means that the bolts connecting the thigh with the net is properly installed and in this case is confirmed link assembly screws thigh with nets and using a long nail, taking into account included the net and move the thigh until it is good to link the four screws.

In the case of the failure of some plates pale wood, it being switch places panels for the possibility of the existence of plates short, but if the lengths of panels equal and continued to the caravan, this indicates the presence of curvature in the femoral bed to abroad and in this case, the panels of Central fall out of place.

To fix this defect can be done installing the board in the middle of the pale thighs bed well after its annexation by using screws or Burmh doubt.

Dislocation or break a wheel chair or

Usually reach the legs and chairs with wheels of the undercarriage (base) and tongue clicking.

In the case of dislocation or break a wheel

May occur dislocation or fracture of a leg cupboard In the case of dislocation one of the legs is support the wheel and then completed off the man carefully as you can use a piece of wood beats them Badakkmag, be sure the safety of the men and the tongue and cleaned of Baia glue the old and then being filled you with glue and install the man in the place and left to dry, but the use of the wheel.

In the case of the man is breaking the wheel support and dismantling of the man as a man who already work in the same dimensions and alternative re-installed in its place, as stated above using the glue.

In the case of dislocation or break a chair

It can follow the same steps above and add to that the legs of the chair are usually reinforced by wooden corners and private dining chairs.

In such cases, the angles are decoded and clean the tongue and you and use glue to install, then re-connect the corners again taking into account the non-use of the chair, but the glue dry.

Might need to use wedges (cut from thin wood gradient in thickness) dipped in glue and knock on the side of the tongue and in the case of breadth clicking on the tongue to contribute to the efficiency of the installation.

In the case of upholstered chair Alantre may be the man installed in a corner gathering Pkoalh Alhenber lower in the case of dislocation or break a man re-install them with glue in the same steps listed at the click of the tongue. M. N

sourse: